Case StudiesExecutive Interviews

Sand 3D printing boosts GRATZ Engineering’s production

Stay up to date with everything that is happening in the wonderful world of AM via our LinkedIn community.

GRATZ Engineering boosted its prototype production by integrating sand 3D printing into its technical business units. The German automotive supplier from the northeast of Baden-Württemberg recognized 3D printing’s enormous potential back in the nineties when it was still a very young technology. Since then, GRATZ has relied on fast metal printing and low-cost 3D printing of sand-casting molds.

 

With 230 employees at six locations in Germany, GRATZ Engineering is a medium-sized company. It has been on the market since 1985, and its engineers turned to 3D printing for parts production at an early stage. The company uses direct metal laser sintering (DMLS) and 3D printing of sand molds for rapid casting. 

 

Andreas Steinbronn, head of parts management at GRATZ, explains why 3D printing has led to immense advantages in manufacturing speed, cost-effectiveness, and a wholly new, disruptive approach to design. DMLS is fast but expensive; 3D sand molding followed by metal casting is comparatively cost-effective, but in some cases not fast enough for rapid prototyping.

 

 

Influences of 3D printing on business models of manufacturers of cast products 

 

Steinbronn: “We work primarily with two technologies: direct metal laser sintering and metal casting using purchased 3D-printed sand cores and molds as well as investment casting patterns in prototype production. Additive manufacturing is used for a good five to ten percent of all our projects. Although 3D printing has been used in the industry for over forty years, the level of integration is still relatively low compared to other processes such as traditional milling. We have had 3D printing on board at GRATZ since the mid-nineties. Our initial assessment at that time was that great opportunities were opening up, simply because of the design freedom. This allowed us to integrate 3D printing into our development processes at a very early stage. This is particularly interesting for the technological and topological optimization of components, mainly to reduce weight. Nowadays, 3D printing has become almost commonplace for us. But, back then, it was a truly disruptive approach, which we continue to pursue more and more today.” 

 

From the prototype center: Rapid Prototyping 

 

Steinbronn: “We are still doing quite a bit of education work that 3D printing offers many advantages. Especially on the customer side, there is plenty of need for information. Speed is one thing, we take DMLS for that. Economy is the other, in which case we favor voxeljet‘s sand casting mold printing. Basically, though, if you can’t mill the raw parts because of very complex geometries, we manufacture them via 3D printing. Especially for prototypes and small series. The portfolio of our parts is quite large. In addition to engine components, the applications extend to all other areas in vehicle but also special machine construction.”

 

Difference between sintered and cast parts 

 

The component quality and material durability of sintered parts are now so good that 99 percent component density is feasible with appropriate rework, and even at high production speeds. However, laser sintering is quite costly due to high material and system prices and still relatively slow build speeds. 

 

Steinbronn continues: “Metal 3D printing like laser sintering is always too expensive if speed is not an issue. If we have two or three weeks for the prototype, we generally prefer to use a combination of classic metal casting with 3D-printed sand molds or investment casting patterns made from PMMA. This cuts costs enormously, and the increased durability and stability of the components is of course also an advantage. The most practical aspects of this are the large building volumes and fast printing rates. With the Binder Jetting printing systems, we can directly produce several variants of our prototypes, such as turbochargers, in parallel and nested on top of each other in one and the same 3D printing process, and not just in one level, as is the case with DMLS. We make the best possible use of the volume of the build space, also known as the job box. This allows us to parallelize the subsequent tests of the casted parts, which saves additional time and reduces the development cycle time. Compared to laser sintering, this still costs a little more time, but we can directly test different variants of the component at the same time in order to define a final design as quickly as possible and release it for production. In addition, we have a much greater variety of materials for casting. We can actually work with any alloy. With sintering, on the other hand, we are much more limited.”

 

 

When to use DMLS and when to use rapid casting? 

 

At the moment, direct metal laser sintering competes with foundries in a comparatively small segment. The building volumes of the DMLS systems are primarily suitable for smaller components that are to be produced extremely quickly. Direct metal 3D printing is, however, also very expensive. 

 

For DMLS, parallel hot isostatic pressing (HIP) is required after additive manufacturing to achieve sufficiently good component density and strength.

 

Steinbronn: “The bottom line is that the average prices for 3D-printed metal components lie around 300 euros per kilogram for aluminum, 400 euros for stainless steel, and up to 1,300 euros per kilogram for special alloys. In a direct comparison, the pure metal casting price is around 6.50 to 32 euros per kilogram, and the liter of printed sand material is around nine euros.”  

 

“With a little more time, we can also economically produce components with complex geometries in batch sizes of one or in small batches of up to one hundred units using rapid casting,” Steinbronn continues. “The prerequisite is that we can produce the molds and cores quickly and cost-effectively, without expensive specialized tooling. This is exactly where industrial 3D printing from voxeljet comes into play.” Called rapid casting, the process prints the molds and cores needed for casting completely without the need for tooling. The printed materials are commonly used in foundries. voxeljet’s VX4000 is currently the world’s largest 3D printing system for sand molds, with a build envelope of 4,000 x 2,000 x 1,000 millimeters. The system enables fast and automated production of the molds using the powerful binder jetting process. The PMMA material set from voxeljet offers another approach. Using this plastic material, patterns can be printed without the need for tools, which can then be processed in the investment casting process in the same way as conventional wax patterns. 

Research 2021
Metal AM Market Opportunities and Trends

This market study from 3dpbm Research provides an in-depth analysis and forecast of the three core segments...

Adam Strömbergsson

Adam is a legal researcher and writer with a background in law and literature. Born in Montreal, Canada, he has spent the last decade in Ottawa, Canada, where he has worked in legislative affairs, law, and academia. Adam specializes in his pursuits, most recently in additive manufacturing. He is particularly interested in the coming international and national regulation of additive manufacturing. His past projects include a history of his alma mater, the University of Ottawa. He has also specialized in equity law and its relationship to judicial review. Adam’s current interest in additive manufacturing pairs with his knowledge of historical developments in higher education, copyright and intellectual property protections.

Related Articles

Back to top button

We use cookies to give you the best online experience. By agreeing you accept the use of cookies in accordance with our cookie policy.

Privacy Settings saved!
Privacy Settings

When you visit any web site, it may store or retrieve information on your browser, mostly in the form of cookies. Control your personal Cookie Services here.

These cookies are necessary for the website to function and cannot be switched off in our systems.

In order to use this website we use the following technically required cookies
  • PHPSESSID
  • wordpress_test_cookie
  • wordpress_logged_in_
  • wordpress_sec

Decline all Services
Accept all Services

STAY AHEAD

OF THE CURVE

Join industry leaders and receive the latest insights on what really matters in AM!

This information will never be shared with 3rd parties

I’ve read and accept the privacy policy.*

WELCOME ON BOARD!