AM ResearchCeramic Additive ManufacturingResearch & Education

MIT researchers 3D print sensors for satellites

These cheap and quick to produce, digitally manufactured plasma sensors could help scientists predict the weather and study climate change

Stay up to date with everything that is happening in the wonderful world of AM via our LinkedIn community.

MIT researchers have created the first completely digitally manufactured plasma sensors for orbiting spacecraft. These plasma sensors, also known as retarding potential analyzers (RPAs), are used by satellites to determine the chemical composition and ion energy distribution of the atmosphere. The 3D printed, and laser-cut hardware performed as well as state-of-the-art semiconductor plasma sensors that are manufactured in a cleanroom – which makes them expensive and requires weeks of intricate fabrication. By contrast, the 3D printed sensors can be produced for tens of dollars in a matter of days.

Due to their low cost and speedy production, the sensors are ideal for CubeSats – inexpensive, low-power, lightweight satellites that are often used for communication and environmental monitoring in Earth’s upper atmosphere.

The MIT researchers developed the RPAs using a glass-ceramic material that is more durable than traditional sensor materials like silicon and thin-film coatings. By using the glass-ceramic in a fabrication process that was developed for 3D printing with plastics, they were able to create sensors with complex shapes that can withstand the wide temperature swings a spacecraft would encounter in lower Earth orbit.

“Additive manufacturing can make a big difference in the future of space hardware. Some people think that when you 3D print something, you have to concede less performance. But we’ve shown that is not always the case. Sometimes there is nothing to trade-off,” said Luis Fernando Velásquez-García, a principal scientist in MIT’s Microsystems Technology Laboratories (MTL), and senior author of a paper presenting the plasma sensors.

Joining Velásquez-García on the paper are Javier Izquierdo-Reyes (lead author and MTL postdoc), Zoey Bigelow (graduate student), and Nicholas K. Lubinsky (postdoc). The research is published in the ‘Additive Manufacturing’ peer-reviewed journal.

MIT researchers 3D print sensors for satellites. These plasma sensors could help scientists predict the weather and study climate change
In an RPA, plasma passes through a series of electrically charged meshes dotted with tiny holes. As the plasma passes through each mesh, electrons and other particles are stripped away until only ions remain. This figure shows how the meshes fit inside the RPA housing, which aligns the meshes. Source: MIT

Versatile sensors

An RPA was first used in a space mission in 1959. The sensors detect the energy in ions, or charged particles, that are floating in plasma, which is a superheated mix of molecules present in the Earth’s upper atmosphere. Aboard an orbiting spacecraft like a CubeSat, the versatile instruments measure energy and conduct chemical analyses that can help scientists predict the weather, or monitor climate change.

The sensors contain a series of electrically charged meshes dotted with tiny holes. As plasma passes through the holes, electrons and other particles are stripped away until only ions remain. These ions create an electric current that the sensor measures and analyzes.

Key to the success of an RPA is the housing structure that aligns the meshes. It must be electrically insulating while also able to withstand sudden, drastic swings in temperature. The MIT researchers used a printable, glass-ceramic material that displays these properties, known as Vitrolite.

Pioneered in the early 20th century, Vitrolite was often used in colorful tiles that became a common sight in art deco buildings. The durable material can also withstand temperatures as high as 800 degrees Celsius without breaking down, whereas polymers used in semiconductor RPAs start to melt at 400 degrees Celsius.

“When you make this sensor in the cleanroom, you don’t have the same degree of freedom to define materials and structures and how they interact together. What made this possible is the latest developments in additive manufacturing,” said Velásquez-García.

MIT researchers 3D print sensors for satellites. These plasma sensors could help scientists predict the weather and study climate change
This figure shows an experiment in which the researchers set up their RPA to characterize it as an ion energy distribution sensor. Source: MIT

The fabrication process

The 3D printing process for ceramics typically involves ceramic powder that is hit with a laser to fuse it into shapes, but this process often leaves the material coarse and creates weak points due to the high heat from the lasers. Instead, the MIT researchers used vat polymerization. With vat polymerization, a 3D structure is built one layer at a time by submerging it repeatedly into a vat of liquid material, in this case – Vitrolite. Ultraviolet light is used to cure the material after each layer is added, and then the platform is submerged in the vat again. Each layer is only 100 microns thick (roughly the diameter of a human hair), enabling the creation of smooth, pore-free, complex ceramic shapes.

In digital manufacturing, objects described in a design file can be very intricate. This precision allowed the researchers to create laser-cut meshes with unique shapes so the holes lined up perfectly when they were set inside the RPA housing. This enables more ions to pass through, which leads to higher-resolution measurements.

Because the sensors were cheap to produce and could be fabricated so quickly, the team of MIT researchers prototyped four unique designs. While one design was especially effective at capturing and measuring a wide range of plasmas, like those a satellite would encounter in orbit, another was well-suited for sensing extremely dense and cold plasmas, which are typically only measurable using ultra-precise semiconductor devices.

According to Velásquez-García, this high precision could enable 3D printed sensors for use in applications in fusion energy research, or supersonic flight. “If you want to innovate, you need to be able to fail and afford the risk. Additive manufacturing is a very different way to make space hardware. I can make space hardware and if it fails, it doesn’t matter because I can make a new version very quickly and inexpensively, and really iterate on the design. It is an ideal sandbox for researchers,” he says.

Velásquez-García reportedly wants to enhance the fabrication process, in the future. Reducing the thickness of layers or pixel size in glass-ceramic vat polymerization could create complex hardware that is even more precise. Moreover, fully additively manufacturing the sensors would make them compatible with in-space manufacturing. He also wants to explore the use of artificial intelligence to optimize sensor design for specific use cases, such as greatly reducing their mass while ensuring they remain structurally sound.

This work was funded, in part, by MIT, the MIT-Tecnológico de Monterrey Nanotechnology Program, the MIT Portugal Program, and the Portuguese Foundation for Science and Technology.

Research 2021
Ceramic AM Market Opportunities and Trends

This market study from 3dpbm Research provides an in-depth analysis and forecast of the ceramic additive ma...

Edward Wakefield

Edward is a freelance writer and additive manufacturing enthusiast looking to make AM more accessible and understandable.

Related Articles

Leave a Reply

Your email address will not be published.

Back to top button

We use cookies to give you the best online experience and for ads personalisation. By agreeing you accept the use of cookies in accordance with our cookie policy.

Privacy Settings saved!
Privacy Settings

When you visit any web site, it may store or retrieve information on your browser, mostly in the form of cookies. Control your personal Cookie Services here.

These cookies are necessary for the website to function and cannot be switched off in our systems.

In order to use this website we use the following technically required cookies
  • PHPSESSID
  • wordpress_test_cookie
  • wordpress_logged_in_
  • wordpress_sec

Decline all Services
Accept all Services

STAY AHEAD

OF THE CURVE

Join industry leaders and receive the latest insights on what really matters in AM!

This information will never be shared with 3rd parties

I’ve read and accept the privacy policy.*

WELCOME ON BOARD!