EnergyIndustrial Additive Manufacturing

Lung-inspired 3D printed heat exchanger could make carbon dioxide power plants a reality

Power generators using supercritical CO2 will be smaller and more efficient

When Charles Parsons invented the steam turbine in 1884, it was a monumental advance. More than a century later, engineers are still relying on steam to operate the turbines that generate much of the world’s power. GE wants to take this technology to the next level by building a CO2 demonstration plant capable of generating of 10-megawatts of electricity and – you guessed it – 3D printing will play a key role in making this possible. How? With a lung-inspired 3D printed heat exchanger.

Leveraging lessons learned human body in biomimicry and generative design, Peter deBock and his colleagues at GE Research in Niskayuna, New York, devised a heat exchanger — an essential component of the cooling system of a power turbine — that mimics human lungs.

Heat exchangers are used in power plants to move energy from the hot exhaust that flows out of the primary gas turbine and transfer it to a secondary turbine power loop, or bottoming cycle, to generate more electricity. This process essentially cools the primary turbine exhaust flow with a “working fluid,” like the antifreeze of a car.

Most bottoming cycles use steam as the working fluid. Conventional alloys and manufacturing methods, however, limit operating temperatures to less than 1,200 degrees Fahrenheit.

New power

Lung-inspired 3D printed heat exchanger
Combining deep expertise in high temperature metal materials, thermal management and additive manufacturing, GE Research Senior Engineer and Metallurgist, Laura Dial, and Peter deBock, a Principal Engineer and specialist in Thermal Management, will work with a team of GE specialists to design an ultra-performing heat exchanger that improves the efficiency profile for both power generation and advanced aerospace applications. Not pictured but also supporting this development are Bill Gerstler, a Principal Engineer in Thermal Management, and Dan Erno, an additive design specialist.

By using other alloys, additive manufacturing and a different working fluid for the bottoming cycle, engineers hope to raise the operating temperature and increase thermal efficiency. Higher temperatures and pressures allow them to pack more punch into a smaller area and extract more energy from it.

One promising working fluid candidate is supercritical carbon dioxide, the gas used in carbonated drinks. When temperature and pressure hit the right conditions, CO2 becomes supercritical, which means that it acquires the density of liquid but flows more like a gas, and holds an enormous amount of heat energy. As a result, a power generator using it as a medium can be 10 times smaller and more efficient than one that uses steam, and also requires fewer parts.

GE Research is involved in a project led by Gas Technology Institute and partnering with Southwest Research Institute to build a $122 million, CO2 demonstration plant capable of generating of 10-megawatts of electricity (MWe).)

Making CO2 supercritical

Supercritical CO2 is a big priority for ARPA-E, the U.S. Department of Energy’s advanced research arm. Recently, ARPA-E put out a call for a new kind of heat exchanger that could help these advanced power plants handle temperatures of 1,650 degrees F — more than 450 degrees higher than current heat exchangers that use steam — at pressures of more than 3,600 pounds per square inch. (Atmospheric pressure at sea level is 14.69 psi.)

Lung-inspired 3D printed heat exchanger
A prototype of a 3D printed heat exchanger designed by GE researchers Dan Erno and Bill Gerstler at GE’s Research campus in Niskayuna, NY. This heat exchanger was designed to have a tri-furcating structure where both fluids split in three directions and recombine continuously throughout the device, mimicking bio-inspired natural concepts like the human lungs to improve thermal efficiency. Images credit: GE Research.

When deBock and his colleagues heard these requirements, their minds went to two advances simmering at GE Research’s labs in Niskayuna: “extreme design skills and extreme metallurgy skills,” deBock says.

Laura Dial, a senior researcher from the metallurgy team, worked to develop an advanced nickel superalloy for use in jet engine parts. The metal is capable of retaining sufficient strength at extremely high temperatures and is also suited for additive manufacturing. “With 3D printing,” says deBock, “we can build design architectures that were previously impossible.”

The ultimate heat exchanger

3D printing paved the way for some radical thinking about how to design a heat exchanger for high temperatures and pressures. DeBock’s team took inspiration from human lungs, which play an important role in helping cool the body to about 98° F. ”Lungs,” says deBock, “are the ultimate heat exchanger.”

The lung accomplishes its heat-exchange function with a network of capillaries, which split the flow of blood into small streams to maximize their exposure to the cooler air coming in from the outside, releasing heat and absorbing oxygen. The GE lung-inspired 3D printed heat exchanger, designed by scientist Dan Erno, does something similar. It takes hot airflow that comes out of the gas turbine and splits and recombines it continuously into a trifurcating network of ducts, each less than 2.5 millimeters in diameter, that are interlaced with another network of channels filled with the colder working fluid (in this case, supercritical CO2) that runs in the opposite direction. The hot air and the working fluid are kept physically separate, but their close proximity allows for efficient heat exchange.

In April, ARPA-E awarded GE a $2.5 million, 2.5-year grant to develop a 50-kilowatt demonstration heat exchanger using its new design. GE’s partners in the project include Oak Ridge National Laboratory, which will contribute expertise in corrosion science to test and validate the material’s long-term performance, and the University of Maryland, which will aid with heat exchanger design and optimization expertise.

Tags

Davide Sher

Since 2002, Davide has built up extensive experience as both a technology journalist and communications consultant. Born in Milan, Italy, he spent 12 years in the United States, where he received his undergraduate degree. Specializing in covering the AM industry, he founded London-based 3D Printing Business Media Ltd. (now 3dpbm) which operates in marketing, editorial and market analysys&consultancy services for the additive manufacturing industry. 3dpbm publishes 3D Printing Business Directory, the largest global directory of companies related to 3DP, as well as several editorial websites, including 3D Printing Media Network and Replicatore. Since 2016 he is also a Senior Analyst for leading US-based firm SmarTech Analysis focusing on the additive manufacturing industry and relative vertical markets.

Related Articles

We use cookies to give you the best online experience. By agreeing you accept the use of cookies in accordance with our cookie policy.

Privacy Settings saved!
Privacy Settings

When you visit any web site, it may store or retrieve information on your browser, mostly in the form of cookies. Control your personal Cookie Services here.

These cookies are necessary for the website to function and cannot be switched off in our systems.

In order to use this website we use the following technically required cookies
  • PHPSESSID
  • wordpress_test_cookie
  • wordpress_logged_in_
  • wordpress_sec

Decline all Services
Accept all Services
Close
Close

STAY AHEAD

OF THE CURVE

Join industry leaders and receive the latest insights on what really matters in AM!

This information will never be shared with 3rd parties

I’ve read and accept the privacy policy.*

WELCOME ON BOARD!