ElectronicsMedicalMedical ResearchResearch & Education

Intertronics supports University of Sheffield with bioelectronics research

Supplying mixing and dispensing equipment to 3D print bioelectronic sensors

Stay up to date with everything that is happening in the wonderful world of AM via our LinkedIn community.

When the Department of Automatic Control and Systems Engineering (ACSE) at The University of Sheffield was looking for a way to accurately 3D print bioelectronic sensors, it reached out to Intertronics for support. The company supplied mixing and dispensing equipment to improve the consistency and quality of the mix – achieve better printing definition and reduced blockages in the nozzle of the 3D printer.

To improve the way recovery from injury and the progression of neurological/musculoskeletal conditions are monitored, the ACSE team is developing a diagnostic glove that includes several flexible 3D printed bioelectronic sensors. The sensors are formed from elastomers mixed with various conductive microparticle and nanoparticle compounds, like graphite, platinum, and silver, which are 3D printed onto the glove’s material.

ACSE team uses an extrusion-based 3D printer to dispense tiny amounts of material. However, during dispensing, particle aggregates were forming and particle distribution was being altered – causing the material to clog in the nozzle. The ACSE team contacted Intertronics, who recommended Preci-Tip Precision Dispensing Tips. Their design has a streamlined conical fluid path that delivers smoother, higher fluid flow rates and lower dispense back pressure compared to most standard dispensing tips – resulting in improved accuracy and significantly reduced clogging. Their industry-standard Luer Lock fitting made the parts compatible with the University’s existing equipment.

Intertronics supports University of Sheffield with bioelectronics research. Mixing and dispensing equipment to 3D print bioelectronic sensors
THINKY mixer

“The customer reported that the Preci-Tips worked well on their highly viscous silicones, they offered good flow, good fluid break off, and stopped agglomerations,” said Paul Whitehead, Strategic Accounts Manager at Intertronics. “The results were better definition and a more reliable system, without blockages during the 3D printing process. However, further discussion revealed that they had challenges with the mixing of the filled polydimethylsiloxane (PDMS) mixtures.”

The process involved mixing nanoparticles into the very viscous PDMS to produce a graphite composite. The ACSE team was adding an organic solvent to reduce the viscosity of the mixture, and therefore aid mixing. The solvent had to be removed post printing – requiring testing to confirm there was no remaining contaminating solvent. There were health and safety considerations for the team in using this approach.

Intertronics then suggested that the team consider trialing a THINKY Mixer to achieve better mixing success. These industrial, non-contact planetary centrifugal mixing machines use both rotation and revolution of material in a container under an acceleration of 400 G to achieve consistent mixing results. In a THINKY Mixer, even materials of very high viscosity, such as those used by the ACSE, can be mixed in a matter of minutes. The THINKY Mixer enables the team to document the exact time and speed of the mixing, which makes the process parameters trackable.

“The THINKY Mixer is a huge improvement on our previous process and means we can achieve consistent outcomes more quickly,” said Tom Paterson, Postdoctoral Research Associate at The University of Sheffield. “We’ve removed the need for solvents, which removes a step from the process, improves health and safety, and removes the regulatory requirement to prove this compound has been removed. The mix quality is extremely good, the mixer doesn’t introduce air into the mix, and we’re making a substantial time-saving.”

Research 2022
Polymer AM Market Opportunities and Trends

This new market study from 3dpbm Research provides an in-depth analysis and forecast of the three core segm...

Edward Wakefield

Edward is a freelance writer and additive manufacturing enthusiast looking to make AM more accessible and understandable.

Related Articles

Back to top button

We use cookies to give you the best online experience and for ads personalisation. By agreeing you accept the use of cookies in accordance with our cookie policy.

Privacy Settings saved!
Privacy Settings

When you visit any web site, it may store or retrieve information on your browser, mostly in the form of cookies. Control your personal Cookie Services here.

These cookies are necessary for the website to function and cannot be switched off in our systems.

In order to use this website we use the following technically required cookies
  • PHPSESSID
  • wordpress_test_cookie
  • wordpress_logged_in_
  • wordpress_sec

Decline all Services
Accept all Services

STAY AHEAD

OF THE CURVE

Join industry leaders and receive the latest insights on what really matters in AM!

This information will never be shared with 3rd parties

I’ve read and accept the privacy policy.*

WELCOME ON BOARD!