AerospaceCase StudiesCompositesItaly

CRP Technology and PoliMi 3D print wind tunnel demonstrator parts

Italian manufacturing company CRP Technology has revealed yet another interesting case study for its composite Windform 3D printing materials, this time in collaboration with the Department of Aerospace Science and Technology at the Politecnico di Milano (PoliMi). CRP Technology provided its 3D printing expertise and composite materials to support PoliMi’s “Aeroelastic Flutter Suppression (AFS)” and “GLAMOUR” projects.

The AFS project, a joint effort between PoliMi and the University of Washington, set out to test different active control system technologies with the aim of attaining Active Flutter Suppression. The GLAMOUR project, for its part, focuses on the technological optimization and experimental validation of Gust Load Alleviation (GLA) control systems for advanced Green Regional Aircraft produced by Leonardo Aircraft Division. For both projects, CRP aided in the additive manufacturing of parts for the aeroelastic wind tunnel demonstrators.

CRP Technology PoliMi wind tunnel
Aeroelastic wind-tunnel demonstrator, AFS project. (Photo: PoliMi)

More specifically, the company helped to manufacture a series of external aerodynamic segments for the projects’ respective wind tunnel demonstrators. CRP leveraged professional selective laser sintering (SLS) 3D printing and its Carbon-composite Windform XT 2.0 material for the tasks. The material was also used to produce a horizontal tail for the AFS wind tunnel demonstrator.

Traditionally, the aerodynamic sections for the wind tunnel demonstrators would have been produced using carbon or glass fiber fabrics dry laminated onto styrofoam blocks cut to match the aircraft’s wing shape. This method did not produce the best results in terms of surface quality and was too time consuming. As showcased through CRP’s efforts, 3D printing proved to be a suitable alternative.

CRP Technology PoliMi wind tunnel
Aeroelastic wind tunnel demonstrator

In the design and development of aircraft components, aerodynamic features are crucial, as they help to reduce drag on the aircraft and enable faster speeds and efficiency. When designing a wing, for instance, aerodynamic features enhance performance and transmit aerodynamic loads to the internal structure.

Other factors also come into play when developing an aircraft wing, including weight and strength. At PoliMi, the team set out to create wing components that were lightweight, stiff and externally smooth.

CRP Technology PoliMi wind tunnel
3D printed aerodynamic sectors, assembly phase, GLAMOUR project. (Photo: PoliMi)

Notably, for the wind tunnel testing phase, the aerodynamic components are not typically subjected to high stress, since they are not the primary structure of the aircraft, but they must fulfil their job of transmitting the aerodynamic forces to the flexible spar, efficiently acting as an interface between the incoming air and the internal structure of the wing. This meant that even for the wind tunnel model, the wing components had to have a high quality surface finish.

CRP Technology worked with PoliMi to optimize the wing components, leveraging SLS 3D printing technology and its composite materials to produce parts that were both smooth and lightweight. Before that, the CRP and PoliMi teams started with an in depth analysis of 2D and 3D files of the aircraft model. At this stage, CRP made recommendations to optimize the geometries of certain parts to help reach the strict weight and stiffness requirements.

CRP Technology PoliMi wind tunnel
Aeroelastic wind-tunnel demonstrator, AFS project.(Photo: PoliMi)

When the 3D models were ready, CRP 3D printed the parts using its Windform XT 2.0 material, whose mechanical properties met the needs of the project in terms of stiffness, weight and surface quality.

In the end, the 3D printed wing components, including connectors for the main spar, hinges and electric drivers, for the AFS project were an overwhelming success. The GLAMOUR project also saw success thanks to CRP technology’s Windform composite material, which enabled the PoliMi team to attain the combination of vibration frequency targets and the forced mass constraints.

CRP Technology wind tunnel
Wind tunnel demonstrator, AFS project. (Photo: PoliMi)
Tags

Tess Boissonneault

Tess Boissonneault moved from her home of Montreal, Canada to the Netherlands in 2014 to pursue a master’s degree in Media Studies at the University of Amsterdam. It was during her time in Amsterdam that she became acquainted with 3D printing technology and began writing for a local additive manufacturing news platform. Now based in France, Tess has over two and a half years experience writing, editing and publishing additive manufacturing content with a particular interest in women working within the industry. She is an avid follower of the ever-evolving AM industry.

Related Articles

We use cookies to give you the best online experience. By agreeing you accept the use of cookies in accordance with our cookie policy.

Privacy Settings saved!
Privacy Settings

When you visit any web site, it may store or retrieve information on your browser, mostly in the form of cookies. Control your personal Cookie Services here.

These cookies are necessary for the website to function and cannot be switched off in our systems.

In order to use this website we use the following technically required cookies
  • PHPSESSID
  • wordpress_test_cookie
  • wordpress_logged_in_
  • wordpress_sec

Decline all Services
Accept all Services
Close
Close

STAY AHEAD

OF THE CURVE

Join industry leaders and receive the latest insights on what really matters in AM!

This information will never be shared with 3rd parties

I’ve read and accept the privacy policy.*

WELCOME ON BOARD!