CERN, the European laboratory hosting the world’s largest particle accelerator, showed the first quadrupole component made for accelerators using laser-based PBF 3D printing and pure copper material. This world-first achievement was made possible by Fraunhofer IWS, together with CERN, Rīgas Tehniskā universitāte (Riga Technical University) and Politecnico di Milano, all partners of the EU-funded project IFAST coordinated by CERN, which aims to enhance innovation in the particle accelerator community and use accelerators to address global societal challenges.
Over 30,000 accelerators are currently in use worldwide, the large majority of which are used for healthcare, environmental and industrial research. This application shows that 3D printing is one way to make them smaller and more cost-effective thus more accessible to users.
Next gen accelerators
A new generation of particle accelerators aims at taking cancer therapy, drug detection and material analysis to a higher level: these linear accelerators are so compact that they are becoming affordable even for smaller hospitals, airports and laboratories. To support this development, the Fraunhofer Institute for Material and Beam Technology IWS, together with the European Organization for Nuclear Research (CERN) in Switzerland, Latvia’s Riga Technology University (RTU) and Politecnico di Milano (PoliMi), is focusing on laser-based 3D printing as mean to streamline production and reduce costs.
As part of the I.FAST project, aimed at enhancing innovation in accelerator and co-funded by the European Commission’s Horizon 2020 program, researchers succeeded for the very first time worldwide in additively manufacturing essential quadrupole components for linear accelerators from pure copper.
This success opens up new prospects for commercial production and practical use of such systems, operating on the principle of high-frequency radio frequency quadrupoles (HF-RFQ). These systems could be used, for example, for better and more automated drug and weapons checks at airports (and even for NDT testing of AM parts, as we reported recently)
The scientists see great potential in 3D copper printing: “This approach will allow us to significantly reduce manufacturing times,” predicted Samira Gruber, an expert in additive manufacturing of pure copper and copper alloys at Fraunhofer IWS. For example, rapid prototyping will accelerate the future development of accelerator technology. In addition, additive manufacturing can save material and thus reduce the resource consumption of copper compared to classic processes.
A green laser quadrupole accelerator revolution
Such arguments will play a major role if these compact accelerators are to become more widely accepted. That’s because high-frequency quadrupoles based on a new technology developed at CERN are the key components and pacemakers for this new generation of facilities. In the quadrupoles, four alternately poled electrodes face each other, arranged like petals around a central particle trajectory. If the user applies an alternating voltage, rapidly changing electric fields will build up. These fields send the particles between the wavy electrode tips on a wave ride that brings them closer and closer to the speed of light with each passing ”electrode petal” with each quadrupole. Unlike their usually huge underground brothers, called ring accelerators, these linear accelerators often take up little more space than a living room.
Because the systems generate a lot of waste heat during long-term operation, the quadrupoles are made of pure copper. This metal is an exceptional conductor of both electricity and heat. Until now, however, the production of quadrupoles has been very complex: they are milled into shape from semi-finished products and then assembled from a very large number of individual parts.
Therefore, Fraunhofer IWS, RTU and PoliMi researchers developed an alternative: they melt pure copper powder using a green laser beam in a PBF process. From this molten metal, they form the quarter segment of a quadrupole. In the process, they save material wherever it is not needed for component strength. In conventional metal processing methods, on the other hand, this component optimization is very time-consuming, and in some places not even feasible at all. As a result, the new production method reduces copper consumption and provides lighter quadrupole segments that can be assembled within one day.
An increase in the build volume of green laser powder bed fusion systems will soon enable entire quadrupole segments to be produced by 3D printing. Nevertheless, the quarter segments produced now are also already capable for the next project phases. For example, the additively manufactured components have rough surface topologies. Therefore, prototypes must be analyzed to understand whether and how the 3D printing quadrupoles need to be subsequently smoothed, for example, by means of plasma, electrochemical or laser polishing. The project agenda also includes tests to determine whether and how minor wear damage on accelerators can be subsequently repaired using additive manufacturing technologies without having to scrap entire components. “In addition, we also intend to study which other materials and components can be considered for additive manufacturing for accelerators,” explained Samira Gruber.
Proton therapy and automatic drug detection
After all, linear accelerators are not only of interest for particle physicists. In the field of medical applications, they can be used for proton therapy against particularly insidious tumors in the abdomen or brain, as well as for medical isotope production. CERN is exploring other applications for the quadrupole accelerators, including material analysis with the purpose of examining art masterpieces.
Accelerators convey considerable market opportunities. There are currently around 30,000 accelerators in use worldwide, estimate Californian industry experts Robert Hamm and Marianne E. Hamm in their 2012 analysis ”Industrial Accelerators and Their Applications”. According to the study, companies and institutes around the world use these systems to manufacture and analyze industrial goods worth $500 billion per year.
Source: Torims, Toms, Pikurs, Guntis, Gruber, S, Vretenar, Maurizio, Ratkus, Andris, Vedani, Maurizio, Lopez, Elena, & Brückner, Frank. (2021). FIRST PROOF-OF-CONCEPT PROTOTYPE OF AN ADDITIVE-MANUFACTURED RADIO FREQUENCY QUADRUPOLE. Zenodo.